Jointing worktops
When joining two worktops together, you should use three standard worktop bolts on each joint. Seal the end grain at both sides of the joint with an appropriate sealer such as MitreSeal before making the joint. Seal the joint with sealer when the parts are finally tightened.
How do you seal oak worktops?
We recommend using Rustins Danish Oil for all worktop oiling and aftercare. We advise applying at least two – three coats on the top and bottom of the worktop, 4 coats on the edges and up to 6 coats on the end grain. You will need to leave up to 8 hours between coats for the oil to be fully absorbed into the surface.
Also, How do you cut solid oak worktops?
To cut wooden worktops, you should use a portable circular saw with at least a 140mm cutting disc, which will cost approximately £100. To create more detailed cuts, apply edge profiles, make irregular cut-outs, or cut features such as hotrod or drainage grooves into your worktop, we recommend using an electric router.
How do I join oak work tops? 5 Golden Rules for Fitting Oak Worktops
- Ensure that the worktop is allowed to acclimatise to the room it is going to be installed in. …
- Measure twice, cut once. …
- If jointing two oak worktops together then it is recommended to use a router and worktop jig to cut a mitre and then joint it using dog bone jointer fixings.
Can you cut oak with a jigsaw?
For softwoods, softer hardwoods (poplar, mahogany, alder, etc.), and sheet goods, run your jigsaw at its highest speed for most cuts. If you encounter resistance, back off the speed slightly. Dense hardwoods, such as cherry, maple, oak, and walnut, call for a slower blade speed to avoid burning.
Table of Contents
How can I make my oak worktop waterproof?
Worktop varnish is the product that requires the least daily maintenance and provides the best protection against water and stains. It makes the wooden worktop waterproof, so that stains are never allowed to become ingrained, even after an overnight exposure. A simple wipe with a sponge is all it takes to remove them.
Should I varnish my oak worktop?
Varnish – though a good choice in some situations – is generally not advised for use in a kitchen. Timber varnishes dry to a relatively brittle, plasticky finish, which can be scratched easily by kitchen knives or cracked by heavy items; the finish is also not very resistant to heat damage.
How do you seal Oak?
Shellac is widely used for sealing oak. One increasingly popular method for finishing oak is to apply an oil stain followed by a coat of shellac to seal the stain. Then fill any blemishes with a grain filler paste, followed by a gel stain. The final finish is a few coats of polyurethane.
Do you cut oak worktops upside down?
Re: Cutting solid oak worktop
no need to flip the top over as you might do with a lam worktop.
Is Oak easy to cut?
Oak is not, however, an easy timber to work as it blunts tools quickly and is so hard it is difficult to sand smooth. The edges splinter easily so gloves are often wise when handling oak. … Needless to say a Danish oil finish compliments oak well.
Will a circular saw cut oak?
As long as your saw has enough power with a quality blade you should be fine.
What is the best tool for cutting worktops?
A circular saw is often the best option to cut laminate worktops. Make sure the blade is sharp (replace the blade if you have been using it for a while) and suitable for fine cuts—it should cut through the worktop without any issue.
Do I need to oil the underside of my worktop?
Before you install your solid wood worktop, it’s really important to oil every surface of the wood to protect it once it has been installed. When you’re doing this, don’t forget to oil every single surface: the underside, the edges and any cut outs you’ve made, or had made in the worktop.
How much should a wooden worktop overhang?
We recommend that your measurements allow for a 20-30mm overhang at the front and exposed edges of your worktop, along with a 3-4mm gap between your worktop and wall (to leave room for sufficient expansion and contraction).
Is Oak hard to cut?
Because of its heavy graining, oak can chip or split easily when routing edges on the stock, removing chunks of material rather than small chips. The result is often far less than desirable. A second tip for working with oak is to make sure that your tools are extremely sharp.
How do you protect oak from water?
There are three surefire ways to waterproof your wood for years to come.
- Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish.
- Seal the wood with coating of polyurethane, varnish, or lacquer.
- Finish and waterproof wood simultaneously with a stain-sealant combo.
How do you protect solid oak worktops?
How To Protect Solid Wood Worktops From Water Damage
- Choose a good quality oil such as Danish Oil, which is a blend of tung and polymerised linseed oil (plus a few added extras to help keep your wood looking good).
- Oil every surface of your worktop (including all the edges and the underside).
Are solid wood worktops worth the hassle?
Wooden worktops are incredibly durable and any knife marks or imperfections are much more easily fixed than with other worktop materials. As long as you look after your worktop and oil it every 6 months, it should last for as long as you want it to. Eco friendly. With wood it’s possible to make eco-friendly choices.
Does Danish oil darken oak worktop?
More than you think – so this small teapot holder, to protect the Welsh Dresser, only has three coats of Danish Oil. Remember that the oil will darken your wood, not as much as some oils or even varnishes, but it will darken the wood as it soaks in. … You can see the original colour of the wood here, a rustic oak.
What is the best finish for oak worktops?
A popular choice for a new kitchen worktop is lighter coloured wood such as oak. For these types of wood, Oil is one of the best finishes to use on its surface. Oil brings out the natural beauty of wood and its grain, whilst offering the essential protection required.
Can I use Danish oil on oak worktops?
Danish oil is a mixture of tung oil and other vegetable oils that can be used to treat wood and keep it looking great for longer. In fact, it is so effective at treating wooden worktops that we have introduced our own special blend -Worktop Express Danish oil for worktops.
Can you leave oak doors untreated?
If you are storing the door it must be kept on a flat dry floor. Any untreated doors must be stored in a dry room, free from any damp. … Leaving oak doors in a wet plastered room will cause the doors to warp as they absorb the excess moisture in the environment.
What is a good finish for oak?
By far the best finishes for high quality wood furniture are either Danish oil or beeswax. They bring out the stunning beauty of wooden furniture grains and leave wood satisfying to the touch. Steer well clear of varnish and polyurethane if you are after a luxurious piece of quality furniture.
Do you need to seal oak?
It is always good to try and finish with a clear coat if possible because if the wood gets scratched it is the clear coat that scratches before the coloured coat and therefore the scratch is not as noticeable. If oak is being oiled it is a good idea to sand it with sandpaper that is no finer than 150 grit.
