The remaining height of the street side face of the fascia board can be determined by deducting the thickness of the bevel cutoff. Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch.
Can you replace fascia board without removing drip edge?
There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board. … Typically, the same gutters can be re-installed on the new fascia board, if they are in good condition. Also, your roofers may need to remove the drip edge.
Also, Can I use 2×4 for fascia board?
Install 1×6-80“ fascia boards to the 2×4 trusses. … Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
How much does it cost to wrap soffit and fascia? Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
Should drip edge be nailed to fascia?
A metal drip edge will help protect the sheathing under the roof, but if it’s installed too closely to the fascia board, it can still cause water to be drawn into the fascia. The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger.
Table of Contents
Can I use 2×6 for fascia?
Depending on what you will be using for a soffiting, you could install a 2×6 over the tails then cover that with a 1×8 for looks and to give a relief for your plywood soffit. If you are installing perf soffiting and covering the fascia, then leave off the 1×8 and install a 2×8 like Ken said.
How do you attach fascia to roof trusses?
Instructions for How to Attach Fascia Board to Roof Trusses
Mark the place closest to the end of the board that aligns with the center of a joist. Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place.
Is sub fascia necessary?
Though not required by building codes, the reasons for subfascia have more to do with evening out the rafter tail irregularities, and providing structural support for the roof edge and gutters. … Another reason many trim manufacturers include 2x subfascia in their installation details is for gutter support.
Do roofers replace fascia boards?
Most roofers, in that case, are generally trained to spot problems in fascia and gutters as well the training required to take care of them. … Fascia both keeps the gutters secure and seals the interior of the attic to some degree. Every so often in the lifespan of your home, you will see fascia repair or replacement.
How long do fascia boards last?
The average lifespan of wooden fascias is usually between 20 – 30 years if they have been maintained. The type of timber used and the quality of the original installation will affect how long they last. If wooden fascia boards are not maintained, they could need replacing in as little as 5 to 10 years.
How much does it cost to replace aluminum soffit and fascia?
The national average materials cost to install an aluminum soffit is $2.58 per linear foot, with a range between $2.06 to $3.11. The total price for labor and materials per linear foot is $10.36, coming in between $6.86 to $13.87. A typical 100 linear foot project costs $1,036.38, with a range of $685.90 to $1,386.85.
How far should drip edge be from fascia?
Drip edge height: 1 5/8″ Drip edge lip extension: 1/2″ Recommended drainage gap: 1/4″ (approx) spaced off of the fascia board.
How far should shingles hang over drip edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.
How do you remove old fascia?
Hold a hammer with your dominant hand behind your existing fascia boards and start pounding it to loosen the nails. Continue hitting the board until the nails behind it come out from the rafters. Once the board is loose, pull it off from your home.
Is cedar good for fascia boards?
Cedar Properties
Pre-primed finger jointed cedar is best used for trim and fascia because of its structural properties. The properties include clear knots, kiln-dried, and tannic acid. … Kiln-dry is dried lumber that makes for strong timber and is moisture, rot, and decay-resistant.
Is cedar good for fascia?
Commonly referred to as a durable species, cedar is a very popular choice for construction, siding, and, yes, fascia boards. … This makes cedar quite an ideal material in terms of retaining its shape while at the same time taking to staining and nailing well.
Can I use Douglas fir for fascia?
Douglas Fir will work for interior or exterior applications. Great for trim, fascia, overhangs, soffits or rustic-look siding. … Clear Douglas Fir is an excellent choice when the finest appearance is required. It is available in many sizes and patterns and can be used for all interior finish applications.
Can I use screws for fascia?
Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.
Does sheathing go over fascia?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. This opens the door to the possibility of water damage by letting gravity work against you.
How do you attach fascia to rafters?
Nail the first fascia board in place with 2-inch finish nails and a hammer. Drive at least two nails through the fascia into the end of each joist. Butt the next fascia piece to the open end of the first so that it it aligned with the center of the joist where the first board ends.
Is fascia required by code?
Sub-fascias are not required by code. The fascia can be nailed directly to the truss tails, but while the sub-fascia is typically a 2x, t…
How do you know when to replace fascia?
How do you know if you need soffit and fascia replacement due to damage? You‘ll see rotting wood, or you’ll notice there’s a leak somewhere. The fascia may look like it needs painting. Paint may peel, or the surrounding areas may look discolored.
Should I replace fascia before or after roof?
While it’s always a good idea to replace damaged fascia as soon as possible, it is essential to ensure it is in good shape before a new roof is installed. Metal eaves drip is an important component in a quality roof installation project.
